This article contains basic instructions for the operation of the TLK 100 device. For full instructions on the operation of the TLK 100, consult the TLK 100 Radio User Guide.
- Talkgroup/Contact list scroll rocker
- On/Off/Info Button
- LED Status Indicator
- Push-to-Talk (PTT) Button
- Volume Button
- Menu/Contact List Button
- LED Display
- USB Port
- Audio Accessory Port
- High Output Speaker
- LTE antenna
- Charging Contacts
Turning the Radio On
Short press the On/Off/Information Button (Button 2).
If successful, the green LED lights up and the display shows a power-on animation.
NOTE: Long press the On/Off/Information Button to power up the radio when the radio is charging.
Follow these steps to configure Wi-Fi on your device.
- From the WOC portal, select the device to which you want to configure the Wi-Fi.
- From the Actions drop-down, select Manage Wi-Fi Networks.
- Enter the configuration details of your Wi-Fi network.
- Turn Off the device.
- Hold PTT button+Power Button+Channel Down for long time. The device comes to the Configure Mode.
- With the help of an USB, connect the the device to your laptop or PC.
- Click Wi-Fi connect and connect to TLK 100 device Wi-Fi.
- Enter the last eight digits of device serial number as password.
- Open browser and enter the URL http://192.168.100.1/
- Click Connect to Wi-Fi Access Point.
- Verify the configuration details and click Submit.
- Click Ok on the message that displays.
- Reboot the device and tap the power button three times to show the Wi-Fi connection.
Configure Enterprise Wi-Fi
Enabling Enterprise Wi-Fi allows a much more secure Wi-Fi access based on WPA/WPA2-Enterprise/802.1x protocol. This enables TLK radios to be deployed over Wi-Fi networks that require WPA-Enterprise-based access. A WPA-Enterprise network requires authentication by the RADIUS server, during connection with the Wi-Fi.
The authentication methods supported by TLK devices are:
- PEAP-MSCHAPv2 (WPA/WPA2)
- EAP-TLS (WPA/WPA2)
- EAP-TTLS-MSCHAPv2 (WPA/WPA2)
EAP-TLS authentication, uses certificate based authentication.
For this configuration of the Wi-Fi, a certificate management server is necessary which is based on Simple Certificate Enrollment Protocol (SCEP) to handle Certificate Enrollment, Renewal and Rollover. The radio automatically renews the certificate before they expire. The configurations setup in SCEP server are used to configure the Enterprise Wi-Fi parameters in the portal.
For this type of authentication, it is necessary to perform the first time onboarding of the device on Enterprise WiFi in a secure network environment. Refer to https://support.waveoncloud.com/wp-content/uploads/2021/09/TLK-Enterprise-WiFi-Onboarding-Guide.pdf
To begin configuration, select the Device and choose Manage Wifi Networks option under Actions tab.
This leads to the “Wifi Networks” setting page, where the configuration for the new Wifi network is to be done.
Following are the required configurations for Enterprise Wi-Fi:
Type – Select Enterprise
Enterprise Security Protocol – Select the type of authentication protocol
Common Name – For EAP-TLS type, this refers to the name to be used for certificate issuance by SCEP Server. For other types enter the name associated with the Enterprise Wi-Fi account.
Password – For EAP-TLS type, this refers to the Challenge Password issued from the SCEP Server. For other types enter the password associated with the Enterprise Wi-Fi account.
SCEP Server URL – This is required for EAP-TLS type only. The URL for SCEP server should be entered here. For other types, just enter “none”.
Root certificate URI – This is to specify a preferred folder name where the root certificate is located.
Making a Group Call
A ‘Group Call’ is a transmission that goes out over a specific Talkgroup. All individuals listening to that Talkgroup will receive the transmission.
To make a group call
- To transmit over the currently selected Talkgroup you may first wish to determine which Talkgroup you currently have selected. Use the Talkgroup/Contact List Scroll Rocker (1) to see and
scroll through the Talkgroup and Contact list.
- Press the PTT button to make the call. The green LED lights up. The display shows the Talkgroup alias.
- Wait for the Talk Permit Tone to end and speak clearly into the microphone. Release the PTT button to listen for a response.
- The green LED blinks when the target radio responds.
The call ends when there is no voice activity for a predetermined period. The radio returns to the screen you were on before initiating the call.
The TLK 100 supports a list of Talkgroups from WAVE. Use the Channel Rocker to select the Talkgroups on the TLK 100 device display.
- Move the Talkgroup/Contact list scroll rocker and stop on the desired Talkgroup.
- Press and hold the Push-to-Talk (PTT) button. Wait until the short alert tone ends before talking.
NOTE: If you hear a continuous beeping error tone then another unit is trying to transmit and you should release the PTT button.
- Release the PTT button when you are done talking.
Making a Private Call
A Private Call is a call from an individual radio to another individual radio.
To make a Private Call
- Long press side button to access the Individual Contacts list. (Button 6).
- Scroll through the contact list using Talkgroup/Contact List Scroll Rocker until the right contact is displayed. You can also use the volume up / down buttons to scroll through the Contact list.
If “X” precedes the contact, then the contact is in Do Not Disturb (DND) mode and a reject tone sounds when PTT button is pressed.
- Press the PTT button to initiate the Private Call. The green LED lights up.The display shows the caller alias.
- Wait for the Talk Permit Tone to end and speak clearly into the microphone. Release the PTT button to allow reception.
- When you are done, press the side button (6) on the device to disconnect the Private Call. Private Calls also timeout after a few seconds of inactivity and the TLK 100 returns to Talkgroup call mode.
Recieving Private Calls
When you receive a Private Call the green LED blinks. Your radio generates an inbound call alert tone before the inbound audio call. You hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is free for you to respond.
- To respond to the call, press PTT button. The green LED lights up.
Wait for the Talk Permit Tone to end and speak clearly into the microphone.
- Release the PTT button to listen.
The call ends when there is no voice activity for a predetermined period.
Understanding Status Indicators
Understanding Battery Indicators